Claims (3)
1. Способ термической переработки бытовых и промышленных отходов, включающий запуск газогенератора путем его предварительного нагрева горячими выхлопными газами двигателя и горячим воздухом воздухонагревателя, дозированную загрузку отходов, предварительно очищенных от металлического лома и строительного мусора, в газогенератор, перемещение перерабатываемых отходов по замкнутому контуру в горячих газах с выжиганием углеродистых остатков, подачу зольных остатков и шлаков в камеру выгрузки через колосниковую решетку, отвод выхлопных, горючих и дымовых газов из газогенератора и чистку газогенератора в период обслуживания, отличающийся тем, что по замкнутому контуру перемещения отходы для пиролиза подогревают горячим воздухом от теплоэлектронагревателей, которые питают энергией электрогенератора двигателя, выхлопные и дымовые газы после катализа угарных газов дожигают при температуре свыше 3000°С, горючие газы и их жидкие продукты после конденсации направляют в дозатор топливной системы двигателя, а выгрузку зольных остатков и шлаков производят путем вращения колосниковой решетки.1. The method of thermal processing of household and industrial waste, including starting the gas generator by pre-heating it with hot exhaust gases of the engine and hot air from the heater, dosed loading of waste previously cleaned from scrap metal and construction waste, into the gas generator, moving the processed waste in a closed circuit to hot gases with burning carbon residues, feeding ash residues and slag into the discharge chamber through the grate, exhaust exhaust , combustible and flue gases from the gas generator and cleaning the gas generator during the service period, characterized in that the waste for pyrolysis is heated using hot air from heat electric heaters that feed the engine's electric energy through a closed loop, and exhaust and flue gases are burned after catalysis of carbon monoxide at temperatures above 3000 ° C, combustible gases and their liquid products after condensation are sent to the fuel metering system of the engine, and the ash residues and slags are unloaded by rotating grating.
2. Пиролизное устройство, содержащее газогенератор с теплоизолирующим кожухом и камерами дозированной загрузки и выгрузки зольных остатков и шлаков, а также швелькамеру с соосно расположенными наружными и внутренними вращающимися шнеками с перфарированными витками и с приводами прямой и обратной подачи, причем рабочие кольцевые полости между витками наружного шнека на входе сообщены с камерой загрузки, а на выходе - с камерой выгрузки, а внутреннего шнека - соответственно с камерой выгрузки и газоотводом, верхние части рабочих кольцевых полостей между витками наружного и внутреннего шнеков сообщены между собой и с газоотводом, а нижняя часть внутреннего шнека сообщена с патрубком подвода выхлопных газов двигателя, а колосниковая решетка выполнена конической, отличающееся тем, что витки наружного шнека выполнены внутренними и образуют совместно с наружными витками внутреннего шнека и цилиндрической стенкой швелькамеры замкнутый контур циркуляции отходов в виде тороидальной рабочей камеры, витки и стенки стволов шнеков и швелькамеры выполнены полыми со встроенными теплоэлектронагревателями, образующими воздухонагреватель замкнутого контура, коническая колосниковая решетка выполнена вращающейся и за одно целое с нижней частью стенки ствола наружного шнека, двигатель оснащен электрогенератором для привода шнеков и теплоэлектронагревателей, а также дозатором подвода горючих газов от газогенератора, причем газоотводные патрубки ствола внутреннего шнека сообщены с катализатором для отделения угарного газа и с камерой прокаливания остатков дымовых и выхлопных газов.2. A pyrolysis device containing a gas generator with a heat-insulating casing and chambers for the metered loading and unloading of ash residues and slags, as well as a channel chamber with coaxially located external and internal rotating screws with perforated coils and with direct and reverse feed drives, and the working annular cavities between the external coils the auger at the inlet is communicated with the loading chamber, and at the outlet, with the unloading chamber, and the internal auger, respectively, with the unloading chamber and gas outlet, the upper parts of the working rings the cavities between the turns of the external and internal screws are connected with each other and with a gas outlet, and the lower part of the internal screw is connected to the pipe for supplying exhaust gases of the engine, and the grate is made conical, characterized in that the turns of the external screw are made internal and form together with the external turns of the internal screw and a cylindrical wall of the channel chamber, a closed loop of waste circulation in the form of a toroidal working chamber, the turns and walls of the shafts of the screws and the channel chamber are made hollow with built-in with electric heaters forming a closed-circuit air heater, the conical grate is rotatable and integrally with the lower part of the barrel wall of the external auger, the engine is equipped with an electric generator to drive the screws and heat electric heaters, as well as a metering device for supplying combustible gases from the gas generator, and the gas outlet pipes of the trunk shaft from the internal auger a catalyst for the separation of carbon monoxide and with an annealing chamber for flue and exhaust gas residues.
3. Устройство по п.1, отличающееся тем, что для катализа резины автомобильных покрышек без предварительного их измельчения швелькамера выполнена со съемной крышкой, а между стенкой швелькамеры и витками внутреннего шнека выполнен зазор для размещения автомобильных покрышек, так, чтобы внутренний шнек проходил через их отверстия, а сам внутренний шнек выполнен съемным с крышкой и его приводом, установленным на крышке.3. The device according to claim 1, characterized in that for catalysis of rubber of automobile tires without preliminary grinding, the channel chamber is made with a removable cover, and a gap is made between the wall of the channel chamber and the turns of the internal screw to accommodate the automobile tires, so that the internal screw passes through them holes, and the internal screw itself is removable with a lid and its drive mounted on the lid.