US887A - Stine - Google Patents

Description

CORNELIUS VAN ALSTINE, 0F MANLIUS CENTER, NEW YORK.

sAWM` itin.

Specification of Letters atent No. 887, dated August 18, 138t To all fao/wm it mag/concern;

Be it known that I, CORNELIUS `VAN AL- sTINE, of Manilus Center, in the county of Onondaga and State of .New York, have inventeda new and useful Machine and an Improved Mode of Sawing; and I do` hereby declare that the following is a full and exact description. Y

The nature of my invention `consists in providing a double or two armed cr'ank and placed in the bottom of a` saw gate, whichwill enable the operation of sawing to be performed with a short crank, by the help of guide arms tothe upper end of the'saw gate, and the saw will clear herselfby repeatedly drawing down the saw dust even with an inch crank only and in the much saving of power consequently when compared with the cranks used in the common saw mills. i

To enable others skilled in the art to make and use my invention I will proceed to describe its construction and operation.

I construct my gate in the usual form of width and height between the girts as gates to other saw mills save the side pieces, which are longer exteriorly below the girts and Alargest transverse with the girts, and the girts are about square. The side pieces also extend above the girt suflicient for thereception of the guide arms, and extend below the lower girt, so as to leave length for the crank to pass through, and the side pieces are left larger below the lower girt about the crank, the same as pitmeny are made in the now used saw mills, but if natural crooks can be had for side pieces I make use of them and let them come together, so as by framing a piece in the bottom of the saw gate let it extend down, so as to bolt the sides to it the crank will pass through the whole width and in this case the crank is in width between the arms to suit the width of the three coupled, and the crank is secured in the same manner in the side pieces by boxes, &c.

Explanation A: Figure 1 represents a back view of the saw gate as seen in the accompanying drawing. Fig. 2 is a bolt passing through the top of the gate above the upper girt high enough to not encroach on the top of the stirrup, is made fast in the gate and is to pass through the guide arms in the inside of the slides and against them. This and the bolt that passes through the other end of the guide arms should be round and perfectly smooth, for in ithem the bolts on `the sills may be of wrought or cast iron i andf secured with wear` irons `and washers against the siflls'and-slides. The width of the crank is in accordance to the` width of the gate, and the length of the arms to meet wishes and circumstances.- I intend to make use of a balance wheel on oneV or each outside of the sills and the crank should be square from the outside of the sills out, if propelled by a flutter wheel then one balance wheel andif driven by a strap a whirl on one or both ends on the outside of the balance wheel, and it may be driven by gearing.

The crankis kept on thesills in the usual i to be performed and the wider the less wear will be realized and the length of the arms equal to the distance from the bolt in the top ses` of the gate to the lower edge of the lower y girt and are placed in between two starts fas-` tened in the upper part `of the frame back of the gate, with a bolt passing through both pins below the level of the one in the top of' the gate, the length of the arm of the crank down, and in those pieces there should be several holes for the purpose of lowering the arms to give rake to saw when she moves down. Those holes are put through on the circle of the arm when in the gate and by dropping down the other end you are taught the circle whereon to make ,the holes. The bolt in the starts should bemade not to move but the arms turn on them. The guide arms are kept apart by `a girt framed in between them, and the distance from `the lower girt to where the crank should be placed in the side pieces is like the size and length of the timbers for the gate and guide arms are `subject to much discretion, as it somewhat depends on the length of the saw and crank made `use of. The mill I built to try the experiment I placed the crank in the side pieces below` the lower girt equal to half the distance from the lower edge of the lower girt to the boltY in the top of the gate.Y I hang the saw in the saine manner Vas inwot-herY saw Vmills. save I give it no rake, which is done by lowering the back end of the-guide-arms.

I make use of fender lports faced with wear plates on both posts and side pieces and feed the same as do other saw mills by the motion of the saw gate, but much finer, as the revolutions may or Will be muchl greater.

Itis also intended besides sawing lumber with the single to use it for sawing staves, &c., witha gang of saws, and I also secure the bottom of;Y the side pieces Yby a stirrup bolted on and Where it is desired make use of composition boxes, and in Vsome instances I attach the side pieces of the saw gate to the Wrist of the crank, thatris to that part lthat pitmen are attached to the cranks now used, and the shank, z'. el the part inside of the arm of the crank and next to them, toI

-restV on the kcrank sills and the power Whirl 'in described, using for the erection any material which will answer its purpose as the occasion may require.k

CORNELIUS VAN ALSTINE.

Vlitnesses:l f v Y JOHN MARIE,

Eni CooK.

Images