US3530A - Current xwater-wheel - Google Patents

Description

JOHN CARNEGY, OF TULLEY, MISSOURI,

CURRENT WATER-WHEEL.

Specification of Letters Patient No. 3,530, datedAprl 10, 1844.

To all 'wit-0m nag/concern: y

Be it known that I, JOHN @kunnen of Tulley, `in the vcounty of Lewis in the State of Missouri, have made certain new and useful Improvements in the Manner of Constructing Current Vater Power Apparatus;

and I do hereby declare that the following is a full andexact description thereof. i

My apparatus `is of that kind in which a number of buckets are y affixed t0 two, or more, endless chains which pass around suitable drums, to which said chains are geared "by teeth on said drums, which teeth take into the linksofthe chains. 'Ihe buckets are, to be, attachedto said chains by hinge joints, so that they may fall over and lie flat upon the chain, as they are carried back on the upper sideof it. The cylinder chains and buckets, with their appendages, are 4to be secured in a proper frame, constituting a part of a hollow trunk, which is to be sustained by two floats, or buoys, in such manner as that the whole apparatus shall rise and fall with the rise and fall of the current in whichit .is placed, inorder that the buckets mayat all times dip to a proper distance into the water, and be acted upon by its full force.` Chains of buckets of this description have been attempted to be used as substitutes for water-wheels; but in these attempts it was found that nearly the whole force of the water was expended on the first bucket on which it impinged, the others consuming by the friction of the parts to which they are attached, nearly as much power as they communicate. 'Io remedy this fault, and render the apparatus more efficient than it has `heretofore proved to be, I affix wing-gates on each side of the hollow trunk that contains the revolving buckets; and I also aflix similar wing-gates on the bottom of said trunk; these wing` gates being so arranged as to cause them successively to collect a portion of the water, that would otherwise pass along on the sides and under -the trunk, to enter it, and to operate on the rear buckets, which without this device would Vbe a burden rather than a benefit to the machine; in most cases,uand probably in all, three such gates on each side, and the saine number on the `bottom of the trunk, will be as many as will be found useful. Theyare to be made to extend, as they succeed each other, to a greater distance from the trunk into the water.

In the accompanying drawing, Figure 1,

is a side view of the 4trunk within which the buckets-revolve. i Fig. 2, is a top view of the timber `which forms one side of the frame work of the trunk. Fig. 3, is a top view `of the frame of the trunk, and of the` two Heats between which it is to be sustained. y at, A, is the frame of the hollow trunk.

y B, B, are buckets which are attached to two, or more, chains, C, C, that `pass around cylinders,`D,` D; which oylindershave pro` jecting teeth, a, a, upon them that engage with the links of the .chain, causing the cylinders to be thereby carried around. The power is to be communicated from one, or more, of the gudgeons of the cylinders, D, I),

to the machinery that is to be driven, which may be done bytoothed gearing, or otherwise.

On the two ends of each of thelbuckets, on that edge of :it which is jointed to the chain, there isa friction wheel, or roller, lil, E, that runs upon ways, F, F, and G, G; the former sustaining the buckets when out of the water, and `the latter sustaining Vthem within it; the lower edge, F, of the side piece F, stands atsuch distance from the rail, G, G, as to check the wheels, or rollers,

E, E, `and prevent their rising.

Z9, Z9, are pieces of timber, which stand at right angles to the buckets, B, B, and c, 0,

are braces which sustain them; the end s of the timbers, b, Z), extend out so as to come nearly into cont-act with the next succeeding bucket, as at Zg; by thus bearing on the link of the `chain that is attached to the bucket by a hinge joint, it is eifectually kept from rising by the force of the water, and thus throwing the bucket out of the vertical line g` they are, consequently, sustained in their proper position as they pass through the trunk. y y i i H, I-I, H, are wing-gates placed below the trunk, and forming a part of its bottom; these dip successively lower and lower into the water, and thus serve more eifectually to force successive portions of it into the trunk and against the buckets. These wing-gates may be raised, or lowered, at pleasure. I, I,

-I, are openings which are toreceive similar wing-gates on each side of the trunk.

I', I', Fig. 2, show the wing-gates open; A, A,\in this gure being the upper side of the frame. These, like the lower gates, may be opened or closed to any desired extent, by means of check ropes, or chains.

In Fig. 3, I have represented only the upper edge of the frame work of the trunk, and of the two oats by which it is to be supported. A, A, is the upper edge of the trunk, and K, K, the upper edge of the two floats, which may be made like scows; but they should be roofed, or decked over, to keep out water which might otherwise enter them from the descent of snow, or rain, or from other causes. The width and depth of these floats, must, of course, be governed by circumstances in each individual case; as, for example, by the size of the apparatus, the depth of water, and the peculiarities of its particular location. L, L, are timbers extending from one of the floats to the other. These are to stand at suoli height above the floats as to enable them to pass over the trunk, A, A, which is to be suspended from them. The timbers, L, L, should be made to slide end-wise through the upper ends of the stanchions M, M, that rise from the floats, so that their distance from the trunk may be regulated. When, in Winter, or from any consideration, it may be necessary to remove the apparatus into a cove, or other place of security, the floats may be moved into contact with the trunk.

To prevent injury to the works from floating timber, or ice, suitable fenders, or gratings, may be erected, or moored, in such manner as the peculiarities of the case may require, or the judgment of the millwright dictate. In all these particulars, the business is to be managed according to known principles. Y

The manner in which l connect my buckets to the endless chains by hinge joints, causes them to enter and leave the water without resistance, as they are enabled thereby to accommodate themselves to its force in their change of position.

Having thus, fully described the nature of my invention, and shown the manner in which the same is carried into operation, what I claim therein as new, and desire to secure by Letters Patent, is

rlhe employment of a series of buckets which are connected by hinge joints to two, or more, lendless chains, in the manner here` in set forth; the shafts of which buckets are furnished with friction wheels, or rollers, that run between ways below and above them, and have stop pieces, such as are shown at Z), l), that extend back so as to come into contact with a link of the chain in the immediate vicinity of the next succeeding bucket, in the manner, and for the purpose, above fully made known, which endless chains of buckets, so arranged, I intend to combine with a floating trunk furnished with wing gates, and otherwise constructed 'as herein described.

JOHN CARNEGY.

Witnesses:

THos. l). JONES, EDWIN L. BRUNDAGE.

Images