Выработка мелких изделий ручным способом или на полуавтоматах , а,также при использовании вакуумных автоматов на ванных печах известных конструкций ограничиваетс недостатком рабочих окон или фронта выработки. Это иоложенк;; не позвол ет полностью использовать производительность ванных печей, вследствие чего снижаетс их к. п. д. Сокращение дл этих целей площади варочной части печи неизбежно приводит к затруднени м создани нормального теплового режима в выработочном бассейне печи.The development of small products by hand or on semi-automatic machines, as well as by using automatic vacuum machines on bath furnaces of known structures, is limited by the lack of working windows or the front of generation. This iolozhenk ;; does not allow to fully utilize the productivity of bath furnaces, as a result of which their efficiency is reduced. Reducing the area of the cooking part of the furnace for these purposes inevitably leads to difficulties in creating a normal thermal regime in the furnace's production pool.
Отличительна особенность предлагаемой печи состоит в толг, что, с целью увеличени фронта выработки и повышени теплового к. п. д. печи, она И1меет выработочный бассейн подковообразной формы, огибающий варочную часть с трех сторон.A distinctive feature of the proposed furnace is that, in order to increase the output front and increase the thermal efficiency of the furnace, it has an horseshoe-shaped working basin that goes around the cooking part from three sides.
На чертеже изоб:ражен план стекловаренной печи.In the drawing, an image: the plan of a glass melting furnace is razhen.
Предлагаема конструкци представл ет собой подковообразную ванную печь / с двум протоками, окруженную с трех сторон выработочным каналом 2, наход щимс под одним сводом с варочной частью 3 печи. Выработочный бассейн отдел етс о.т варочного двум стенками 4 из огнеупорных брусьев, между которыми дл охлаждени стенки, обращенной к варочной части печи, вентил тором 5 продуваетс воздух высокого давлени . После охлаждени степки этот воздух поступает в печь дл горени . Стенки выработочного бассейна печи изолируют теплоизол ционным материалом 6, устанавливаемым также на стенке выработочного бассейна печи в промежутке между стенками варочной и выработочпой частей печи. Дно выработочной и варочной частей печи общее.The proposed design is a horseshoe-shaped bath furnace / with two ducts, surrounded on three sides by the working channel 2, which is under one arch with the cooking part 3 of the furnace. The production pool is separated from the cooking chamber by two walls 4 from refractory bars, between which high pressure air is blown out to cool the wall facing the cooking part of the furnace with fan 5. After the steppe has cooled, this air enters the furnace for burning. The walls of the furnace's working pool are insulated with heat insulating material 6, also installed on the wall of the furnace's working pool in the gap between the walls of the cooking and working parts of the furnace. The bottom of the working and cooking parts of the furnace is common.
Установка единого свода и всего «колпака над варочпой и выработочпой част ми печи позвол ет обеспечить меньщий износ п т свода, а также допускает смену стен-решеток варочного отделени на ходу печи, удлин тем самым врем работы печи без ремонтаInstalling a single roof and the entire hood over the cooker and the working parts of the oven allows for less wear on the roof of the roof and also allows changing the wall-grates of the cooking compartment on the oven’s path, thereby extending the oven’s operation time without repair.