мотки отключени 13, стопа 14, кожуха 15 с немагнитной вставкой 16 и пружины 17, располагаемой между дном стакана 9 и выступом 7 илока запорного органа.coils off 13, foot 14, casing 15 with a non-magnetic insert 16 and a spring 17 located between the bottom of the cup 9 and the protrusion 7 of the valve body.
Устройство работает следующим образом.The device works as follows.
Под действием пружины 10 запориый орган 6 перекрывает штуцер 5, а штуцеры 2 и 3 сообшаютс между собой, обмотка включени 8 обесточена (данное положение изображено на чертеже). Усили посто нного магнита 12 недостаточно дл переключени запорного органа, так как магнитна проводимость воздушного зазора 5 мала и магнитный поток замыкаетс по шунтирующей цепи через кожух 15 с немагнитной вставкой 16. При подаче напр жени на обмотку включени 11 начинаетс движение кор 8 со стаканом 9, при этом пружины 10 и 17 будут сжиматьс . В конце хода, когда усилие привода значительно возрастает, выступ 7 запорного органа 6 будет подхвачен кольцевым упором стакана 9 и запорный орган 6 откроет штуцер 5. Когда корь 8, прижметс к стопу 14 (т.е. 6 станет равным нулю), движение запорного органа будет происходить под действием пружины 17, котора обеспечит прижатие клапана к верхнему седлу в корпусе 1, тем самым штуцеры 2 и 3 окажутс разъединенными . При сн тии напр жени с обмотки включени 11 корь- 8 останетс в этом положении, так как он удерживаетс магнитным потоком посто нного магнита 12, замыкающимс через стоп 14 и корь 8 с насаженным на него стаканом . Дл переключени запорного органа 6 необходимо подать импульс напр жени на обмотку отключени 13, при этом возникает магнитный поток, равный и противоположный по направлению магнитному потоку посто нного магнита 12. Под действием пружины 10 корь 8 возвращает запорный орган 6 в исходное положение (изображенное на чертеже). Подача давлени может осуществл тьс через любой из трех штуцеров, что зависит от назначени пневмо- или гидросистемы, в которую устанавливаетс клапан.Under the action of the spring 10, the locking organ 6 closes the nozzle 5, and the nozzles 2 and 3 communicate with each other, the turn-on winding 8 is de-energized (this position is shown in the drawing). The magnet 12 force is not enough to switch the closure member, since the magnetic conductivity of the air gap 5 is small and the magnetic flux closes along the shunt circuit through the case 15 with a non-magnetic insert 16. When voltage is applied to the turn-on winding 11, the movement of the core 8 with the cup 9 begins in this case, the springs 10 and 17 will compress. At the end of the stroke, when the drive force increases significantly, the protrusion 7 of the locking member 6 will be picked up by the annular abutment of the cup 9 and the locking member 6 will open the nozzle 5. When the measles 8 is pressed to the foot 14 (i.e. 6 will become zero), the locking movement The body will occur under the action of the spring 17, which will ensure that the valve is pressed against the upper seat in the housing 1, thereby fittings 2 and 3 will be disconnected. When removing the voltage from the turn-on winding, the 11 bark-8 will remain in this position, as it is held by the magnetic flux of the permanent magnet 12, which is closed through the stop 14 and the bark 8 with the glass mounted on it. To switch the locking member 6, it is necessary to apply a voltage pulse to the disconnecting winding 13, and a magnetic flux occurs that is equal and opposite in direction to the magnetic flux of the permanent magnet 12. Under the action of the spring 10, the locking organ 8 returns the locking organ 6 to its original position (shown in the drawing ). Pressure can be supplied through any of the three fittings, depending on the purpose of the pneumatic or hydraulic system in which the valve is installed.