Дл обособлени плавильного и рафинажного или других пространств стеклоплавильной ванны известны устройства, состо щие из подвижной по вертикали, . пропущенной через сводовую щель перегородки или щирмы из огнеупорных плит. В предлагаемом устройстве щирма собрана из вплотную примыкающих друг к другу огнеупорных плит, подвещенных к общей балочной поддержке. Означенные плиты могут быть выполнены однослойными или двуслойными подвешены кажда в отдельности к общей подъемной балке, а также снабжены подвесными ущирени ми и кромочными фальцами. Дл подъема, опускани и установки на определенной высоте подвесной балки, служащей дл укреплени составной перегородки, применены подвесные балки или иные при- способлени .To separate the melting and refining or other spaces of the glass-melting bath, devices consisting of a vertically movable, are known. passed through the arched gap of the partition or shchirmy of refractory plates. In the proposed device, the shield is assembled from closely adjacent to each other refractory plates, shared with the general beam support. These plates can be made single-layer or double-layer, each individually suspended from a common lifting beam, and also equipped with suspension girders and edge seams. Suspended beams or other methods were used to raise, lower and install at a certain height of the suspension beam, which serves to reinforce the composite partition.
На чертеже фиг. 1 изображает вертикальный разрез устройства; фиг. 2 - деталь вертикально-поперечного разреза огнеупорной.плиты.In FIG. 1 shows a vertical section of the device; FIG. 2 is a detail of a vertical-transverse section of the refractory plate.
Предлагаемое устройство состоит из нескольких огнеупорных плит такой длины , чтобь при предельном опускании устройства нижний край плит коснулс зеркала стекла. Плиты сбоков имеют кромочные фальцы 7. дл плотного соединени их в сплощную щтору; кажда плита (2)The proposed device consists of several refractory plates of such a length so that when the device is extremely lowered, the lower edge of the plates touched the glass mirrors. Sides of the sides have flanges 7. for tightly joining them into a flattened chrator; each plate (2)
в отдельности подвещиваетс к жесткой швеллерной подъемной балке 3 при помощи т г из круглого железа 4, планок и гаек 5. Кажда плита имеет головку, за KOTopyib она схватываетс двум неравнобокими угольниками б, ст гиваемыми болтами 1 (фиг. 2). Т ги 4, подвещивающие плиту к балке 3, проход т через одну из полок угольников, обнимают болт 1 кольцом, имеющимс на нижнем конце т ги, и закрепл ютс гайко 8 болта. Плиты делаютс или одинарные или двойные, при чем в последнем случае , так как обща толщина плит (штор) будет досаточно больщой, в каждой из двойных плит дл облегчени их весаследует делать отверсти , не приход щиес друг против друга, и сечение их уменьшать к концу плиты.separately, it is connected to a rigid channel lifting beam 3 with the help of tons of round iron 4, planks and nuts 5. Each plate has a head, for KOTopyib it is grasped by two equally angled squares, bolts 1 (Fig. 2). The rods 4, which guide the slab to the beam 3, pass through one of the square shelves, hug the bolt 1 with the ring at the bottom end of the rod, and fasten the nut 8 of the bolt. The plates are made either single or double, and in the latter case, since the total thickness of the plates (curtains) will be sufficiently large, in each of the double plates to facilitate their weight, holes should be made not facing each other, and their cross section should be reduced by the end slabs.
Клепанна щвеллерна подъемна балка 3 при помощи роликов, троса 10 и цепи 11 подвещиваетс к стропильным фермам 12 здани через блок 13; общий вес всей щторы уравновешиваетс соответствующими грузами 14, аодвешенными к свободному концу троса 15. На оси блока 16 укрепл етс второй блокзубчатка 17, сцепл емый черв ком 18 с приводным механизмом 19, вращаемым снизу, на полу здани ванной печи, от руки. Дл предупреждени падени шторы в печь, в случае разрыва тросов илиA riveted iron bar lift beam 3 with the help of rollers, cable 10 and chain 11 is connected to the trusses 12 of the building through block 13; the total weight of the whole bucket is balanced by the corresponding weights 14 attached to the free end of the cable 15. On the axis of the block 16, the second block of the shank 17, coupled by the screw 18 with the drive mechanism 19, rotated from below, on the floor of the stove, is fixed. To prevent the curtains falling into the oven, in case of cable breaks or