8000 GitHub - OLIMEX/ESP32-EVB: ESP32 WiFi / BLE Development board with Ethernet interface, Relays, microSD card · GitHub
[go: up one dir, main page]

Skip to content
  • OLIMEXPublic

    About

    ESP32 WiFi / BLE Development board with Ethernet interface, Relays, microSD card

    Resources

    Stars

    289 stars

    Watchers

    31 watching

    Forks

    Latest commit

     

    History

    76 Commits

    Folders and files

    NameName
    Last commit message
    Last commit date
     
     
     
     
     
     
     
     
     
     

    Repository files navigation

    ESP32-EVB

    ESP32 wifi / BLE development board with Ethernet, relays, microSD card, CAN, infrared, Li-Po charger, GPIOs.

    Product page: https://www.olimex.com/Products/IoT/ESP32/ESP32-EVB/open-source-hardware

    Open-source hardware board made with open-source CAD software. Comes with either ESP32-WROOM-32E or ESP32-WROOM-32UE module, depending on variant. Board vairants are:

    Board variant ESP32 module External antenna Temperature range
    ESP32-EVB ESP32-WROOM-32E No 0-70°C
    ESP32-EVB-EA ESP32-WROOM-32UE Yes 0-70°C
    ESP32-EVB-EA-IND ESP32-WROOM-32UE Yes -40+85°C
    ESP32-EVB-IND ESP32-WROOM-32E No -40+85°C

    ESP32-EVB - ESP32-WROOM-32E module, no external antenna, commercial temeprature range 0-70°C

    ESP32-EVB-EA - ESP32-WROOM-32UE module, fitting external antenna, commercial temeprature range 0-70°C

    ESP32-EVB-EA-IND - ESP32-WROOM-32UE module, fitting external antenna, industrial temeprature range -40+85°C

    ESP32-EVB-IND - ESP32-WROOM-32E module, no external antenna, industrial temeprature range -40+85°C

    You can find design hardware sources, schematic exports, BOMs, and more, in the "HARDWARE" folder.

    You can find ESP-IDF and Arduino IDE examples, in the "SOFTWARE" folder.

    FAQ


    Q: I have some trouble downloading my code to ESP32-EVB. Is there a way to force boot mode?

    A: By default the board comes without BOOT button functioanlity. However, we have providedan option to can convert user BUT1 into BOOT button to force button but this requires hardware change and soldering. Soldering experience is required since it is a tight spot. You need to perform two changes:

    • Solder the pads of R46 together (or solder 0R resistor in 0603 size in the R46 position there);
    • Unsolder R14 and solder its pads together (or again solder 0R resistor in 0603 size in the R14 position).

    After the two changes, to manually force boot mode, hold button BUT1 then reset the board with RST1. Both R46 and R14 are near the button BUT1. Notice that the button will still act as user button after the initial boot sequence. You can find more about what changing these resistors does if you inspect the schematic.


    Q: The Ethernet doesn't start after a restart, it throws "init phy failed" error. What should I do?

    A: Ethernet might hang of initialized too quickly after a reset. Add some delay at the start of the code before the Ethernet initialization. For example, if you are using the default Arduino IDE demo for LAN8720 try adding delay () after Serial.begin(), as shown below:

    void setup()
    {
    Serial.begin(115200);
    delay (2000);
    WiFi.onEvent(WiFiEvent);
    ETH.begin();
    }
    

    About

    ESP32 WiFi / BLE Development board with Ethernet interface, Relays, microSD card

    Resources

    Stars

    289 stars

    Watchers

    31 watching

    Forks

    Releases

    Packages

    Contributors

    Languages

    0