Repository navigation
uefi: fall back to the Graviton UART when the SPCR points into memory - #75
Open
Martin-Lndbl wants to merge 1 commit into
Open
Martin-Lndbl wants to merge 1 commit into
Martin-Lndbl wants to merge 1 commit into
Conversation
Since 2026-10-14 the Graviton3 (c7g) firmware in eu-north-1 describes its console as a 16550 at 0x80000000 with byte access. That address is the end of the low RAM block in the UEFI memory map, not a device; the UART is still the 16550 at 0x90a0000 with dword registers it always was. The kernel took the table at its word and hung in the serial driver's first poll before it could print anything, so every c7g boot showed only "miniosv UEFI stub starting". Graviton4 (c8g) firmware is unaffected. The stub now checks the SPCR address against the memory map when the ACPI OEM ID is AMAZON: an address inside, or exactly at the end of, a non-MMIO entry is memory, and the stub substitutes the known Graviton layout and says so. Other firmware is trusted as before. A diagnostic line prints the SPCR fields and the OEM ID, since this is the only trace a Graviton boot leaves when the console pick is wrong. Verified on c7g.large: the kernel boots in 345 ms and the PMU benches run. Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_016x6mtxvvKCfAojAVKt4ZYe
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
in favor of #64 (since my fork is going private)
Since 2026-10-14 the Graviton3 (c7g) firmware in eu-north-1 describes its console as a 16550 at 0x80000000 with byte access. That address is the end of the low RAM block in the UEFI memory map, not a device; the UART is still the 16550 at 0x90a0000 with dword registers it always was. The kernel took the table at its word and hung in the serial driver's first poll before it could print anything, so every c7g boot showed only "miniosv UEFI stub starting". Graviton4 (c8g) firmware is unaffected.
The stub now checks the SPCR address against the memory map when the ACPI OEM ID is AMAZON: an address inside, or exactly at the end of, a non-MMIO entry is memory, and the stub substitutes the known Graviton layout and says so. Other firmware is trusted as before. A diagnostic line prints the SPCR fields and the OEM ID, since this is the only trace a Graviton boot leaves when the console pick is wrong.
Verified on c7g.large: the kernel boots in 345 ms and the PMU benches run.
Claude-Session: https://claude.ai/code/session_016x6mtxvvKCfAojAVKt4ZYe