Repository navigation
Description
Problem
The current driver always uses the first sensor for screen orientation. On this device, that is the base sensor, so screen rotation does not follow the display reliably.
Basic information
- Laptop model: CHUWI MiniBook X N150
- Linux distro: NixOS 26.05 (Yarara), build 26.05.20260914.c3eea5b
uname -aoutput:Linux chewbacca 6.18.51 #1-NixOS SMP PREEMPT_DYNAMIC Fri Sep 11 09:49:46 UTC 2026 x86_64 GNU/Linux
The repository diagnostic scripts are not NixOS-aware. check-status.sh assumes DKMS and traditional /usr, /lib, and /etc package paths, so it reports working NixOS packages as missing. The equivalent information below was collected from the running kernel, the NixOS system closure, systemd, sysfs, and the configured VBT.
Equivalent to tools/check-status.sh
--- device ---
dmi vendor CHUWI Innovation And Technology(ShenZhen)co.,Ltd
dmi product MiniBook X
cpu Intel(R) N150
microcode 0x21
bios DNN20A V2.51 04/16/2025
display card1-DSI-1 1200x1920
sleep mode S0ix (software)
--- kernel cmdline ---
i915.vbt_firmware vbt
i915.enable_psr 0 (disabled)
--- configured VBT ---
refresh 90.00 Hz (clock=246385 kHz, htotal=1268, vtotal=2159)
rotation 90 degrees (1)
--- NixOS kernel modules ---
goodix_ts installed, loaded
minibook_ec installed, loaded
dptf_enabler installed, loaded
i2c_designware_spklen installed, loaded
goodix firmware present in the active system closure
--- services ---
thermald 2.5.11.minibook1, enabled, running
iio-sensor-proxy 3.9.minibook1, linked, running
sensor polling active
MINIBOOK_PANEL_ORIENTATION=normal
MINIBOOK_LAPTOP_ORIENTATION=right-up
MINIBOOK_ORIENTATION_SENSOR=display
Equivalent to tools/detect-hardware.sh
ID DRIVER NAME
dmi:vendor <empty> CHUWI Innovation And Technology(ShenZhen)co.,Ltd
dmi:product <empty> MiniBook X
dmi:bios <empty> DNN20A V2.51 04/16/2025
cpu:0 <empty> Intel(R) N150
pci:8086:46d4 i915 Intel Corporation Alder Lake-N [Intel Graphics]
pci:8086:461d proc_thermal_pci Intel Corporation Alder Lake Innovation Platform Framework Processor Participant
pci:8086:54ed xhci_hcd Intel Corporation Alder Lake-N PCH USB 3.2 Gen 2x1 (10 Gb/s) xHCI Host Controller
pci:8086:54f0 iwlwifi Intel Corporation Alder Lake-N PCH CNVi WiFi
pci:8086:54c4 sdhci-pci Intel Corporation Alder Lake-N eMMC Controller
pci:8086:54c8 snd_hda_intel Intel Corporation Alder Lake-N PCH High Definition Audio Controller
pci:1d97:1202 nvme Shenzhen Longsys Electronics Co., Ltd. Lexar NM610 PRO NVME SSD (DRAM-less) (rev 01)
usb:8087:0026 usb <empty>
usb:1b0a:2bc9 usb Hy-Usb2.0-1*MIC
i2c:GDIX1002 Goodix-TS Goodix Capacitive TouchScreen
i2c:MDA6655 mxc4005 <empty>
i2c:XXXX0000 i2c_hid_acpi XXXX0000:05 0911:5288 Touchpad
acpi:ACPI0003 <empty> <empty>
acpi:ACPI000C <empty> <empty>
acpi:ACPI000E <empty> <empty>
acpi:GDIX1002
7544
<empty> <empty>
acpi:INT33A1 <empty> <empty>
acpi:INT33D3 <empty> <empty>
acpi:INT340E <empty> <empty>
acpi:INTC1041 <empty> <empty>
acpi:INTC1046 <empty> Thermistor Ambient
acpi:INTC1049 <empty> Intel PCH FIVR Participant
acpi:INTC1057 <empty> <empty>
acpi:INTC1060 <empty> Platform Power
acpi:INTC1061 <empty> Battery 1 Participant
acpi:INTC1070 <empty> <empty>
acpi:INTC1099 <empty> <empty>
acpi:MDA6655 <empty> <empty>
acpi:MSFT0001 <empty> <empty>
acpi:MSFT0101 tpm_crb TPM 2.0 Device
acpi:PNP0103 <empty> <empty>
acpi:PNP0C02 <empty> <empty>
acpi:PNP0C02 <empty> <empty>
acpi:PNP0C02 <empty> <empty>
acpi:PNP0C09 ec <empty>
acpi:PNP0C0A battery <empty>
acpi:PNP0C0C button <empty>
acpi:PNP0C0D button <empty>
acpi:PNP0C0E button <empty>
acpi:PRP00001 <empty> <empty>
acpi:PRP00001 <empty> <empty>
acpi:XXXX0000 <empty> <empty>
blk:nvme0n1 driver AirDisk 512GB SSD (476 GB)
drm:card1-DSI-1 <empty> Internal panel 1200x1920
backlight:intel_backlight <empty> raw
hwmon:hwmon0 <empty> nvme
hwmon:hwmon1 <empty> minibook_soc
hwmon:hwmon2 <empty> minibook_charger
hwmon:hwmon3 <empty> minibook_fan
hwmon:hwmon4 <empty> acpitz
hwmon:hwmon5 <empty> ADP1
hwmon:hwmon6 <empty> BAT0
hwmon:hwmon7 <empty> coretemp
hwmon:hwmon8 <empty> iwlwifi_1
tpm:tpm0 <empty> v2
Evidence
I moved each half of the laptop separately while recording both sensors. This showed:
- I2C0 / raw1 = base sensor
- I2C1 / raw2 = display sensor
cal1is identitycal2changes(x, y, z)to(x, -y, -z)
For screen orientation, the working input is the raw display reading with X reversed:
raw2 -> (-x, y, z) -> existing orientation filter
Using calibrated a2 instead adds a 180 degree rotation around X and gives the wrong orientation. Hinge-angle calculation still needs both calibrated sensors and should not change. Note that previously we were using cal1, which is equivalent to raw1 on this machine as it uses the identity matrix. So switching to raw for both should leave the old setting effectively the same,
Requested change
Add an optional setting:
MINIBOOK_ORIENTATION_SENSOR=base|display
It should select only the raw input to the existing orientation filter. Sensor discovery, calibration, and hinge calculation should stay unchanged. The default should remain base.
I have tested display on this hardware. Auto-rotation follows the display correctly.
We could consider making the display the default value if testing on other devices correlates with this result.
Activity
fstanis commentedon Sep 17, 2026
Finally, some of those odd bugs make so much sense...
Absolutely, it makes no sense to ever use
base, unless the sensors can be opposite on some devices. I'll test this on my device and see if there's some other way we can detect this.