8000 minix/man/man8/boot.8 at R3.2.0 · krackou/minix · GitHub
[go: up one dir, main page]

Skip to content

Latest commit

 

History

History
651 lines (651 loc) · 15 KB

boot.8

File metadata and controls

651 lines (651 loc) · 15 KB
The values
.Ar enabled , on
will enable module loading for
.Cm boot
and
.Cm multiboot ,
whereas
.Ar disabled , off
will turn off the feature.
.It Ic multiboot Va kernel Op Ar arguments
Boot the specified
.Va kernel ,
using the
.Dq multiboot
protocol instead of the native
.Nx
boot protocol.
The
.Va kernel
is specified in the same way as with the
.Ic boot
command.
.Pp
The multiboot protocol may be used in the following cases:
.Bl -tag -width indent
.It Nx Ns / Ns Xen No kernels
The
.Tn Xen
DOM0 kernel must be loaded as a module using the
.Ic load
command, and the
.Tn Xen
hypervisor must be booted using the
.Ic multiboot
command.
Options for the DOM0 kernel (such as
.Dq -s
for single user mode) must be passed as options to the
.Ic load
command.
Options for the hypervisor (such as
.Dq dom0_mem=256M
to reserve 256 MB of memory for DOM0)
must be passed as options to the
.Ic multiboot
command.
See
.Xr boot.cfg 5
for examples on how to boot
.Nx Ns / Ns Xen.
.It Nx No multiboot kernels
A
.Nx
kernel that was built with
.Cd options MULTIBOOT
(see
.Xr multiboot 8 )
may be booted with either the
.Ic boot
or
.Ic multiboot
command, passing the same
.Ar arguments
in either case.
.It Non- Ns Nx No kernels
A kernel for a
.No non- Ns Nx
operating system that expects to be booted using the
multiboot protocol (such as by the GNU
.Dq GRUB
boot loader)
may be booted using the
.Ic multiboot
command.
See the foreign operating system's documentation for the available
.Ar arguments .
.El
.It Ic quit
Reboot the system.
.It Ic userconf Va command
Pass the
.Va command
to
.Xr userconf 4
at boot time .
These commands are processed before the interactive
.Xr userconf 4
shell is executed, if requested .
.It Ic vesa Bro Va modenum | Ar on | off | enabled | disabled | list Brc
Initialise the video card to the specified resolution and bit depth.
The
.Va modenum
should be in the form of
.Ar 0x100 , 800x600 , 800x600x32 .
The values
.Ar enabled , on
put the display into the default mode, and
.Ar disabled , off
returns the display into standard vga mode.
The value
.Ar list
lists all supported modes.
.El
.Pp
In an emergency, the bootstrap methods described in the
.Nx
installation notes for the i386 architecture
can be used to boot from floppy or other media,
or over the network.
.Sh FILES
.Bl -tag -width /usr/mdec/bootxx_fstype -compact
.It Pa /boot
boot program code loaded by the primary bootstrap
.It Pa /boot.cfg
optional configuration file
.It Pa /netbsd
system code
.It Pa /netbsd.gz
gzip-compressed system code
.It Pa /usr/mdec/boot
master copy of the boot program (copy to /boot)
.It Pa /usr/mdec/bootxx_fstype
primary bootstrap for filesystem type fstype, copied to the start of
the
.Nx
partition by
.Xr installboot 8 .
.El
.Sh SEE ALSO
.Xr ddb 4 ,
.Xr pciback 4 ,
.Xr userconf 4 ,
.Xr boot.cfg 5 ,
.Xr boot_console 8 ,
.Xr dosboot 8 ,
.Xr halt 8 ,
.Xr installboot 8 ,
.Xr mbr 8 ,
.Xr multiboot 8 ,
.Xr pxeboot 8 ,
.Xr reboot 8 ,
.Xr shutdown 8 ,
.Xr w95boot 8 ,
.Xr boothowto 9
.Sh BUGS
The kernel file name must be specified before, not after, the boot options.
Any
.Ar filename
specified after the boot options, e.g.:
.Pp
.Bd -unfilled -offset indent -compact
.Cm boot -d netbsd.test
.Ed
.Pp
is ignored, and the default kernel is booted.
.Pp
Hard disks are always accessed by
.Tn BIOS
functions.
Unit numbers are
.Tn BIOS
device numbers which might differ from numbering in the
.Nx
kernel or physical parameters
.Po
e.g.,
.Tn SCSI
slave numbers
.Pc .
There isn't any distinction between
.Dq sd
and
.Dq wd
devices at the bootloader level.
This is less a bug of the bootloader code than
a shortcoming of the PC architecture.
The default disk device's name printed in the starting message
is derived from the
.Dq type
field of the
.Nx
disklabel (if it is a hard disk).
0