You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
changed the title [-]https://home.miot-spec.com/spec?type=urn:miot-spec-v2:device:fan:0000A005:dmaker-02:1[/-][+]Support for Dream Maker Smart Fan[/+]on Feb 27, 2025
Maybe, if that chip in the middle reading "ARM" is the mcu.
But it should be easy to find out:
Wire your 3.3v uart ttl to the TX/RX/GND labeled pads on the bottom left and fetch the serial output while booting up the board. That log of the vendor firmware should be enough to find out if this board is supported.
I got it connect, but i think my flash backup ist not ok, so i did not dare to flash it.
In the config from miot2esphome rx / tx Pin is missing, is it the same like other wroom?
`st:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5848
load:0x40078000,len:9392
ho 0 tail 12 room 4
load:0x40080000,len:6112
entry 0x40080330
�[0;32mI (30) boot: ESP-IDF v3.1.6-dirty 2nd stage bootloader�[0m
�[0;32mI (30) boot: compile time 15:07:25�[0m
�[0;32mI (31) boot: Enabling RNG early entropy source...�[0m
�[0;32mI (35) boot: SPI Speed : 40MHz�[0m
�[0;32mI (40) boot: SPI Mode : DIO�[0m
�[0;32mI (44) boot: SPI Flash Size : 4MB�[0m
�[0;32mI (48) boot: Partition Table:�[0m
�[0;32mI (51) boot: ## Label Usage Type ST Offset Length�[0m
�[0;32mI (59) boot: 0 nvs WiFi data 01 02 00009000 00004000�[0m
�[0;32mI (66) boot: 1 otadata OTA data 01 00 0000d000 00002000�[0m
�[0;32mI (73) boot: 2 phy_init RF data 01 01 0000f000 00001000�[0m
�[0;32mI (81) boot: 3 factory factory app 00 00 00010000 00100000�[0m
�[0;32mI (88) boot: 4 ota_0 OTA app 00 10 00110000 00100000�[0m
�[0;32mI (96) boot: 5 ota_1 OTA app 00 11 00210000 00100000�[0m
�[0;32mI (103) boot: End of partition table�[0m
�[0;32mI (108) esp_image: segment 0: paddr=0x00110020 vaddr=0x3f400020 size=0x2bca8 (179368) map�[0m
�[0;32mI (180) esp_image: segment 1: paddr=0x0013bcd0 vaddr=0x3ffc0000 size=0x03aa8 ( 15016) load�[0m
�[0;32mI (186) esp_image: segment 2: paddr=0x0013f780 vaddr=0x40080000 size=0x00400 ( 1024) load�[0m
�[0;32mI (187) esp_image: segment 3: paddr=0x0013fb88 vaddr=0x40080400 size=0x00488 ( 1160) load�[0m
�[0;32mI (196) esp_image: segment 4: paddr=0x00140018 vaddr=0x400d0018 size=0xb83e8 (754664) map�[0m
�[0;32mI (469) esp_image: segment 5: paddr=0x001f8408 vaddr=0x40080888 size=0x16ce0 ( 93408) load�[0m
�[0;32mI (522) boot: Loaded app from partition at offset 0x110000�[0m
�[0;32mI (522) boot: Disabling RNG early entropy source...�[0m
�[0;32mI (523) cpu_start: Pro cpu up.�[0m
�[0;32mI (526) cpu_start: Starting app cpu, entry point is 0x40081078�[0m
�[0;32mI (0) cpu_start: App cpu up.�[0m
�[0;32mI (537) heap_init: Initializing. RAM available for dynamic allocation:�[0m
�[0;32mI (543) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM�[0m
�[0;32mI (549) heap_init: At 3FFD2F18 len 0000D0E8 (52 KiB): DRAM�[0m
�[0;32mI (555) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM�[0m
�[0;32mI (562) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m
�[0;32mI (568) heap_init: At 40097568 len 00008A98 (34 KiB): IRAM�[0m
�[0;32mI (574) cpu_start: Pro cpu start user code�[0m
�[0;32mI (257) cpu_start: Starting scheduler on PRO CPU.�[0m
�[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m
�[0;32mI (325) DM-LOG: ap->ssid:,key:*********[0m
�[0;32mI (325) DM-LOG: BLE:paired model:0�[0m
�[0;32mI (325) DM-LOG: ota information->mcu_firmware_flag:0,mcu_firmware_length0!�[0m
�[0;32mI (335) DM-LOG: wifi firmware version:dmiot_v1.1.0�[0m
�[0;32mI (1345) DM-LOG: serial send msg->
action:2,
resouce:232a,
msg_id:0,
data_length:0
checksum enable
�[0m
�[0;32mI (1445) DM-LOG: serial received msg->
length:89,
action:82,
resouce:232a,
msg_id:0,
data_length:80
checksum enable
�[0m
�[0;32mI (1445) BTDM_INIT: BT controller compile version [382a548]
�[0m
�[0;32mI (1445) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
�[0;32mI (1515) phy: phy_version: 4009, e7844c0, Jul 15 2019, 13:20:06, 0, 0�[0m
�[0;32mI (1845) DM-LOG: wifi station mode, start connect to ap �[0m
I (1865) wifi: wifi driver task: 3ffb7a18, prio:23, stack:3584, core=0
�[0;32mI (1865) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
�[0;32mI (1865) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
I (1895) wifi: wifi firmware version: 3c46a62
I (1895) wifi: config NVS flash: enabled
I (1895) wifi: config nano formating: disabled
I (1895) wifi: Init dynamic tx buffer num: 32
I (1895) wifi: Init data frame dynamic rx buffer num: 32
I (1905) wifi: Init management frame dynamic rx buffer num: 32
I (1905) wifi: Init management short buffer num: 32
I (1915) wifi: Init static rx buffer size: 1600
I (1915) wifi: Init static rx buffer num: 10
I (1925) wifi: Init dynamic rx buffer num: 32
I (1935) wifi: mode : sta (98:f4:ab:24:ff:f8)
�[0;32mI (1935) DM-LOG: connect to ap SSID:********password:************�[0m
�[0;32mI (1945) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
I (2065) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
I (2065) wifi: state: init -> auth (b0)
I (2075) wifi: state: auth -> init (8a0)
I (2075) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
�[0;32mI (2075) DM-LOG: station:disconnected ap�[0m
�[0;32mI (2145) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (2855) DM-LOG: serial received msg->
length:9,
action:2,
resouce:78,
msg_id:0,
data_length:0
checksum enable
�[0m
�[0;32mI (2855) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (4135) DM-LOG: station:disconnected ap�[0m
�[0;32mI (4145) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
I (4255) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
I (4255) wifi: state: init -> auth (b0)
I (4275) wifi: state: auth -> assoc (0)
I (4285) wifi: state: assoc -> run (10)
I (4315) wifi: connected with NAME_AP, channel 1
I (4315) wifi: pm start, type: 1
That looks different to what my purifier prints. While I do see the raw serial communication, here it's just mentioned, but it's not clear if it's really the miot serial protocol, which is what we need.
So I think you need to try yourself and check what the esp32 gets from the mcu over serial.
For that you have two options:
Don't touch the fw and sniff the serial communication between the two chips
Flash a bare esphome fw and check
All esp32 configs here have tx_pin=17 and rx_pin=16, so that's what I would try here first for either option.
For 2), make sure flashing via bootloader works, and use that to make a fw backup first.
Hard to tell, maybe the serial between the two chips use rts/cts and you
can't sniff it wired like you have atm.
I'd probably just flash a bare esphome config with "level: VERBOSE" to
see what the comms look like. But of course you'd have to make sure you
have a proper fw backup to go back to in case the device is imcompatible.
I tried to backup the fw multiple times, mostly the esp reboots, the few times it worked i get different files, so i don't dare to flash esphome.
I will give it another try if i have more time.
Maybe anybody else with a dreammaker will give it a try.
I think this fans are not using the Xiaomi Miot Serial Communication, so i gave up right now.
As workaround i use the dmiot2mqqt
If someone has done some more research, we could reopen the issue
To avoid ESP32 reboot issue you need to short the Reset pin of the MCU to the GND.
on the fan board is 5 pins right next to ROHS sign that where you will find Reset and GND
I just soldered small SMD switch to be able to do it many times as I flash firmware
also in case you missed the Boot pin next to UART pins must be also connected to GND and ESP32 will show in serial that its In download mode
for the MCU side UART on IO 16 and 17 I noticed that baud rate 19200 works best.
when ESP32 is not in boot mode and MCU is works normal it seams like MCU is restarting the ESP every 5-10 minutes
Let me know if u find something, My Backup contains my private wifi passwords... but I would like to get esphome working so tell me if i can support you.
I working on it for three days already and no luck of successfully controlling it with custom firmware
a lot of info found all thanks to Claude etc.
main struggle is the communication to MCU what I discovered but not sure about it is that MCU constantly asking for wifi status and reboots ESP after 5-10 minutes I am assuming in order to be able to control it need more digging
so far what I can share is the data that was captured with simple UART sniffer Arduino sketch
I am no where near to be an expert in any of this its all just for fun to challenge my self and create something that works.
here is what I found useful so far
Physical buttons serial captured with UART sniffer Arduino sketch flashed on to ESP32 Wroom 32D UART pins GPIO16, GPIO17 MCU side UART
The fan board also have EEPROM in my case HT24LC02U3T026G6
Timer ON (entered timer selection if no button pressed second time it will exit without timer set)
HEX:
FA CE 00 09 02 00 78 00 00 00 00 00 00 4B ......x......K
Great captures, thanks! We (me & Claude Sonnet 4.6) analyzed the binary firmware dump alongside your UART captures and can now map the complete protocol.
The MCU likely stops rebooting the ESP once it sees status 02 or 03. Try 03 if 02 doesn't stop the reboot — it may expect cloud connectivity confirmation.
Note: the response resource 0x70 came from the firmware binary, not from your captures — you only sniffed RX (GPIO16). To fully confirm, sniff TX (GPIO17) with the original firmware running.
Hello @BobeOlsen, can you still switch between the original and esphome fw? i did some research, but i didn't get the uart to run, could you test some settings with the dreammaker app? i think Byte 27 ist the oscillation angle, it also can be moved left an right, also please set the timer to 8 hours in the app. i did some work here, but i can't confirm if it is working: https://github.com/d0np3p3/esphome-dreammaker-fan
Hi
I did successfully revert back to OG firmware multiple times
I do not use the esphome for my needs i wanted to us it with homekit and homespan library in arduino
Here is what currently have have for byte map not sure how accurate is it but works for me
UART/Serial data in HEX captured on GPIO17 TX————>MCU RX while controlling fan from the App.
Turn ON with smart breeze mode
FA CE 00 0C 04 23 47 00 00 28 BC 00 03 00 00 01 2A
Turn ON with direct breeze mode
FA CE 00 0C 04 23 47 00 00 F1 BD 00 03 00 00 01 F4
Turn ON with direct breeze mode
FA CE 00 0C 04 23 47 00 00 47 30 00 03 00 00 01 BD
Turn OFF
FA CE 00 0C 04 23 47 00 00 0D 86 00 03 00 00 00 D8
Turn OFF
FA CE 00 0C 04 23 47 00 01 6F 8B 00 03 00 00 00 40
Turn OFF
FA CE 00 0C 04 23 47 00 00 02 63 00 03 00 00 00 AA
Switched to natural breeze
FA CE 00 0C 04 23 47 00 01 29 CE 00 03 00 02 01 40
Switched to direct breeze
FA CE 00 0C 04 23 47 00 01 59 38 00 03 00 02 00 D9
Set speed to level 2
FA CE 00 0C 04 23 47 00 01 61 ED 00 03 00 01 28 BD
Set speed to level 3
FA CE 00 0C 04 23 47 00 00 82 F9 00 03 00 01 3F 00
Set speed to level 4
FA CE 00 0C 04 23 47 00 01 2D 62 00 03 00 01 64 3A
Turned ON oscillation with preset 90 degree
FA CE 00 0C 04 23 47 00 00 E7 80 00 03 00 03 01 B0
Changed oscillation to 30 degree
FA CE 00 0C 04 23 47 00 00 BA 72 00 03 00 04 1E 93
Changed oscillation to 60 degree
FA CE 00 0C 04 23 47 00 00 49 07 00 03 00 04 3C D5
Changed oscillation to 120 degree
FA CE 00 0C 04 23 47 00 00 87 13 00 03 00 04 78 5B
Changed oscillation to 140 degree
FA CE 00 0C 04 23 47 00 00 80 B7 00 03 00 04 8C 0C
Notification sound ON
FA CE 00 0C 04 23 47 00 00 3F 7C 00 03 00 07 01 08
Notification sound OFF
FA CE 00 0C 04 23 47 00 00 6B 08 00 03 00 07 00 BF
Child Lock ON
FA CE 00 0C 04 23 47 00 00 17 F8 00 03 00 09 01 5E
Child Lock OFF
FA CE 00 0C 04 23 47 00 00 43 05 00 03 00 09 00 96
LED indication ON
FA CE 00 0C 04 23 47 00 01 6D DB 00 03 00 08 01 97
LED indication OFF
FA CE 00 0C 04 23 47 00 01 0C EF 00 03 00 08 00 49
Scheduled Turn-OFF set to OFF
FA CE 00 0D 04 23 47 00 01 6B C3 00 04 00 06 00 00 7C
Scheduled Turn-OFF set to 1
FA CE 00 0D 04 23 47 00 01 02 76 00 04 00 06 00 3C 02
Scheduled Turn-OFF set to 2
FA CE 00 0D 04 23 47 00 00 A0 9D 00 04 00 06 00 78 02
Scheduled Turn-OFF set to 3
FA CE 00 0D 04 23 47 00 00 0E C8 00 04 00 06 00 B4 D7
Scheduled Turn-OFF set to 4
FA CE 00 0D 04 23 47 00 00 9D DE 00 04 00 06 00 F0 B8
Scheduled Turn-OFF set to 5
FA CE 00 0D 04 23 47 00 01 12 FF 00 04 00 06 01 2C 8C
Scheduled Turn-OFF set to 6
FA CE 00 0D 04 23 47 00 00 C1 58 00 04 00 06 01 68 CF
Scheduled Turn-OFF set to 7
FA CE 00 0D 04 23 47 00 01 16 D5 00 04 00 06 01 A4 DE
Scheduled Turn-OFF set to 8
FA CE 00 0D 04 23 47 00 00 2C FE 00 04 00 06 01 E0 58
Thank you, i got it with your findings, i didn't get output from mcu.
Esphome runs and working, some small issues to fix,and test long running.
See my repo.
Thank you, i got it with your findings, i didn't get output from mcu. Esphome runs and working, some small issues to fix,and test long running. See my repo.
Glad the info was useful that means I actually did something that works
Same here works fine with homekit also few tweaks needed
You mean the code/sketch?
I dont want to deal with all the github way of doing it like repo or whatever its called
I can just paste arduino sketch here and if it will help somebody else that would be nice
here is the ArduinoIDE HomeSpan sketch that currently is running on the fans ESP32 Wroom 32D with Apple homekit just fine there is some minor issue that could be fixed I think but generally speaking it works great no random disconnection etc.
Also attached is reverse engineered protocol created by Claude AI
Thanks to d0np3p3 for checksum hint (plain 8-bit sum)
Now moving on to zhimi.fan.za3 Xiaomi Smartmi Standing Fan 2
Hello has anybody, maybe @BobeOlsen access to the mcu communication and can test what happens if you try to pair a remote, I am still trying to get it work....
Everything else is working fine with Esphome.
Correction to my earlier comment in this thread — the 0x70 response I posted
was speculation read out of the firmware binary, never verified against a
real capture. It is wrong, and I'd rather flag it than leave people building on
it.
Wrong (my earlier guess):
FA CE 00 09 81 00 70 02 00 00 00 00 00 C4
^^ action 81 ^^ resource 0x70
Correct, confirmed from live UART captures (original firmware running
against a simulated MCU on a test bench):
action: 0x82
resource: 0x0078 <- echoes the QUERY resource, there is no 0x70
The MCU polls with action:2, resource:0x0078 roughly every 60 s, and the ESP
answers action:0x82 on the same resource. The response payload is 56 bytes:
FA CE 00 44 82 00 78 [msg_id 4B] 00 3B
64 6D 69 6F 74 5F 76 31 2E 31 2E 30 00 00 00 00 "dmiot_v1.1.0" (16 B)
7A 65 69 63 6F 5F 33 2E 30 2E 30 00 00 00 00 00 "zeico_3.0.0" (16 B)
35 63 30 31 33 62 62 66 36 30 64 63 00 00 00 00 "5c013bbf60dc" (16 B)
00 00 00 00 01 00 01 02 00 02 status bytes (8 B)
[checksum]
Offset
Len
Content
0
16
comm_version, ASCII, null-padded
16
16
firmware_version, ASCII, null-padded
32
16
12-hex-digit device ID, ASCII (device-specific)
48
8
status bytes, meaning still unclear
Without a response the MCU pulls the ESP's EN pin low and reboots it after
about four minutes, so this one matters if you're writing your own firmware.
This is also consistent with @BobeOlsen's independent app captures in this
thread — those matched our resource mapping 1:1, including the exact angle
bytes (0x1E/3C/78/8C = 30/60/120/140°) and timer values
(0x3C/78/B4/F0 = 1–4 h).
Optional addition — only if you want to mention the remote
The BLE remote work is on a beta branch and needs a per-device key, so it may
be more noise than help for that thread. Include only if it seems welcome:
Unrelated but possibly interesting for this thread: the original DM-FCB01
remote turned out to broadcast each button press as a BLE advertisement
(company ID 0x4D44), with an 8-byte payload encrypted using single DES in
ECB mode. The key is stored per device in the fan's NVS as ble_key.
Decrypted, the payload holds the pressed button, the complete target state
and a checksum — so the remote can keep working after flashing ESPHome,
without re-pairing. Details: https://github.com/d0np3p3/esphome-dreammaker-fan/blob/v4.0.0-beta/PROTOCOL.md
Activity
[-]https://home.miot-spec.com/spec?type=urn:miot-spec-v2:device:fan:0000A005:dmaker-02:1[/-][+]Support for Dream Maker Smart Fan[/+]dhewg commentedon Feb 28, 2025
Maybe, if that chip in the middle reading "ARM" is the mcu.
But it should be easy to find out:
Wire your 3.3v uart ttl to the TX/RX/GND labeled pads on the bottom left and fetch the serial output while booting up the board. That log of the vendor firmware should be enough to find out if this board is supported.
d0np3p3 commentedon Feb 28, 2025
I got it connect, but i think my flash backup ist not ok, so i did not dare to flash it.
In the config from miot2esphome rx / tx Pin is missing, is it the same like other wroom?
`st:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5848
load:0x40078000,len:9392
ho 0 tail 12 room 4
load:0x40080000,len:6112
entry 0x40080330
�[0;32mI (30) boot: ESP-IDF v3.1.6-dirty 2nd stage bootloader�[0m
�[0;32mI (30) boot: compile time 15:07:25�[0m
�[0;32mI (31) boot: Enabling RNG early entropy source...�[0m
�[0;32mI (35) boot: SPI Speed : 40MHz�[0m
�[0;32mI (40) boot: SPI Mode : DIO�[0m
�[0;32mI (44) boot: SPI Flash Size : 4MB�[0m
�[0;32mI (48) boot: Partition Table:�[0m
�[0;32mI (51) boot: ## Label Usage Type ST Offset Length�[0m
�[0;32mI (59) boot: 0 nvs WiFi data 01 02 00009000 00004000�[0m
�[0;32mI (66) boot: 1 otadata OTA data 01 00 0000d000 00002000�[0m
�[0;32mI (73) boot: 2 phy_init RF data 01 01 0000f000 00001000�[0m
�[0;32mI (81) boot: 3 factory factory app 00 00 00010000 00100000�[0m
�[0;32mI (88) boot: 4 ota_0 OTA app 00 10 00110000 00100000�[0m
�[0;32mI (96) boot: 5 ota_1 OTA app 00 11 00210000 00100000�[0m
�[0;32mI (103) boot: End of partition table�[0m
�[0;32mI (108) esp_image: segment 0: paddr=0x00110020 vaddr=0x3f400020 size=0x2bca8 (179368) map�[0m
�[0;32mI (180) esp_image: segment 1: paddr=0x0013bcd0 vaddr=0x3ffc0000 size=0x03aa8 ( 15016) load�[0m
�[0;32mI (186) esp_image: segment 2: paddr=0x0013f780 vaddr=0x40080000 size=0x00400 ( 1024) load�[0m
�[0;32mI (187) esp_image: segment 3: paddr=0x0013fb88 vaddr=0x40080400 size=0x00488 ( 1160) load�[0m
�[0;32mI (196) esp_image: segment 4: paddr=0x00140018 vaddr=0x400d0018 size=0xb83e8 (754664) map�[0m
�[0;32mI (469) esp_image: segment 5: paddr=0x001f8408 vaddr=0x40080888 size=0x16ce0 ( 93408) load�[0m
�[0;32mI (522) boot: Loaded app from partition at offset 0x110000�[0m
�[0;32mI (522) boot: Disabling RNG early entropy source...�[0m
�[0;32mI (523) cpu_start: Pro cpu up.�[0m
�[0;32mI (526) cpu_start: Starting app cpu, entry point is 0x40081078�[0m
�[0;32mI (0) cpu_start: App cpu up.�[0m
�[0;32mI (537) heap_init: Initializing. RAM available for dynamic allocation:�[0m
�[0;32mI (543) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM�[0m
�[0;32mI (549) heap_init: At 3FFD2F18 len 0000D0E8 (52 KiB): DRAM�[0m
�[0;32mI (555) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM�[0m
�[0;32mI (562) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM�[0m
�[0;32mI (568) heap_init: At 40097568 len 00008A98 (34 KiB): IRAM�[0m
�[0;32mI (574) cpu_start: Pro cpu start user code�[0m
�[0;32mI (257) cpu_start: Starting scheduler on PRO CPU.�[0m
�[0;32mI (0) cpu_start: Starting scheduler on APP CPU.�[0m
�[0;32mI (325) DM-LOG: ap->ssid:,key:*********[0m
�[0;32mI (325) DM-LOG: BLE:paired model:0�[0m
�[0;32mI (325) DM-LOG: ota information->mcu_firmware_flag:0,mcu_firmware_length0!�[0m
�[0;32mI (335) DM-LOG: wifi firmware version:dmiot_v1.1.0�[0m
�[0;32mI (1345) DM-LOG: serial send msg->
action:2,
resouce:232a,
msg_id:0,
data_length:0
checksum enable
�[0m
�[0;32mI (1445) DM-LOG: serial received msg->
length:89,
action:82,
resouce:232a,
msg_id:0,
data_length:80
checksum enable
�[0m
�[0;32mI (1445) BTDM_INIT: BT controller compile version [382a548]
�[0m
�[0;32mI (1445) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
�[0;32mI (1515) phy: phy_version: 4009, e7844c0, Jul 15 2019, 13:20:06, 0, 0�[0m
�[0;32mI (1845) DM-LOG: wifi station mode, start connect to ap �[0m
I (1865) wifi: wifi driver task: 3ffb7a18, prio:23, stack:3584, core=0
�[0;32mI (1865) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
�[0;32mI (1865) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE�[0m
I (1895) wifi: wifi firmware version: 3c46a62
I (1895) wifi: config NVS flash: enabled
I (1895) wifi: config nano formating: disabled
I (1895) wifi: Init dynamic tx buffer num: 32
I (1895) wifi: Init data frame dynamic rx buffer num: 32
I (1905) wifi: Init management frame dynamic rx buffer num: 32
I (1905) wifi: Init management short buffer num: 32
I (1915) wifi: Init static rx buffer size: 1600
I (1915) wifi: Init static rx buffer num: 10
I (1925) wifi: Init dynamic rx buffer num: 32
I (1935) wifi: mode : sta (98:f4:ab:24:ff:f8)
�[0;32mI (1935) DM-LOG: connect to ap SSID:********password:************�[0m
�[0;32mI (1945) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
I (2065) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
I (2065) wifi: state: init -> auth (b0)
I (2075) wifi: state: auth -> init (8a0)
I (2075) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
�[0;32mI (2075) DM-LOG: station:disconnected ap�[0m
�[0;32mI (2145) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (2855) DM-LOG: serial received msg->
length:9,
action:2,
resouce:78,
msg_id:0,
data_length:0
checksum enable
�[0m
�[0;32mI (2855) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (4135) DM-LOG: station:disconnected ap�[0m
�[0;32mI (4145) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
I (4255) wifi: n:1 0, o:1 0, ap:255 255, sta:1 0, prof:6
I (4255) wifi: state: init -> auth (b0)
I (4275) wifi: state: auth -> assoc (0)
I (4285) wifi: state: assoc -> run (10)
I (4315) wifi: connected with NAME_AP, channel 1
I (4315) wifi: pm start, type: 1
�[0;32mI (4325) DM-LOG: station:connected ap ,waitting for ip acquisition�[0m
�[0;32mI (4845) DM-LOG: esp_get_free_heap_size:92672�[0m
�[0;32mI (5345) event: sta ip: 192.168.179.9, mask: 255.255.255.0, gw: 192.168.179.1�[0m
�[0;32mI (5345) DM-LOG: got local ip address:192.168.179.9�[0m
�[0;32mI (5445) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (6435) DM-LOG: remote_tcp_send_buffer:->
{"action": 1,"resource_id":2001,"version":"zeico_3.0.0","code":0,"msg_id":0,"data":{"product_id":"5e7af43818828a4ea7d67e3a","device_id":"64940f35f74b69e8823805fa","device_key":"HCUv7LRF9BmkXqoA","comm_version":"dmiot_v1.1.0","rf_version":"v3.1.6","mcu_version":"fan_0001"}}�[0m
�[0;32mI (6515) DM-LOG: remote tcp clinet receive data: {"action":81,"resource_id":2001,"version":"zeico_3.0.0","code":0}
�[0m
�[0;32mI (6515) DM-LOG: remote tcp data parse->server have login�[0m
�[0;32mI (6525) DM-LOG: serial send msg->
action:82,
resouce:78,
msg_id:0,
data_length:3b
checksum enable
�[0m
�[0;32mI (7845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (10845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (13845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (16535) DM-LOG: remote_tcp_send_buffer:->
{"action": 1,"resource_id":127,"version":"zeico_3.0.0","data":{"comm_version":"dmiot_v1.1.0","rf_version":"v3.1.6","mcu_version":"fan_0001","signal":100}}�[0m
�[0;32mI (16635) DM-LOG: remote tcp clinet receive data: {"action":81,"resource_id":127,"version":"zeico_3.0.0","code":0}
�[0m
�[0;32mI (16845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (19845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (22845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (25845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (26535) DM-LOG: remote_tcp_send_buffer:->
{"action": 1,"resource_id":127,"version":"zeico_3.0.0","data":{"comm_version":"dmiot_v1.1.0","rf_version":"v3.1.6","mcu_version":"fan_0001","signal":86}}�[0m
�[0;32mI (26595) DM-LOG: remote tcp clinet receive data: {"action":81,"resource_id":127,"version":"zeico_3.0.0","code":0}
�[0m
�[0;32mI (28845) DM-LOG: esp_get_free_heap_size:87284�[0m
�[0;32mI (29545) DM-LOG: serial received msg->
length:24,
action:84,
resouce:2347,
msg_id:0,
data_length:1b
checksum enable
�[0m
�[0;32mI (29555) DM-LOG: remote_tcp_send_buffer:->
{"action": 84, "version":"zeico_3.0.0","resource_id":9031,"msg_id":0,"code":0,"data":{"source":"manual","deviceException":4194304,"useException":0,"power":0,"mode":0,"speed":100,"roll_enable":0,"roll_angle":90,"power_delay":0,"sound":0,"light":1,"child_lock":0,"temperature":0.0,"humidity":0.0,"ext1":97,"ext2":102,"ext3":13363,"ext4":14385,"ext5":943206968,"ext6":1630823777}}�[0m
�[0;32mI (31845) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (34845) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (36545) DM-LOG: remote_tcp_send_buffer:->
{"action": 1,"resource_id":127,"version":"zeico_3.0.0","data":{"comm_version":"dmiot_v1.1.0","rf_version":"v3.1.6","mcu_version":"fan_0001","signal":100}}�[0m
�[0;32mI (37625) DM-LOG: remote tcp clinet receive data: {"action":81,"resource_id":127,"version":"zeico_3.0.0","code":0}
�[0m
�[0;32mI (37855) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (40855) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (41125) DM-LOG: serial received msg->
length:24,
action:84,
resouce:2347,
msg_id:0,
data_length:1b
checksum enable
�[0m
�[0;32mI (41125) DM-LOG: remote_tcp_send_buffer:->
{"action": 84, "version":"zeico_3.0.0","resource_id":9031,"msg_id":0,"code":0,"data":{"source":"manual","deviceException":4194304,"useException":0,"power":1,"mode":0,"speed":100,"roll_enable":0,"roll_angle":90,"power_delay":0,"sound":0,"light":1,"child_lock":0,"temperature":0.0,"humidity":0.0,"ext1":97,"ext2":102,"ext3":13363,"ext4":14385,"ext5":943206968,"ext6":16308 10BC8 23777}}�[0m
�[0;32mI (42115) DM-LOG: serial received msg->
length:24,
action:84,
resouce:2347,
msg_id:0,
data_length:1b
checksum enable
�[0m
�[0;32mI (42115) DM-LOG: remote_tcp_send_buffer:->
{"action": 84, "version":"zeico_3.0.0","resource_id":9031,"msg_id":0,"code":0,"data":{"source":"manual","deviceException":4194304,"useException":0,"power":1,"mode":0,"speed":100,"roll_enable":1,"roll_angle":90,"power_delay":0,"sound":0,"light":1,"child_lock":0,"temperature":0.0,"humidity":0.0,"ext1":97,"ext2":102,"ext3":13363,"ext4":14385,"ext5":943206968,"ext6":1630823777}}�[0m
�[0;32mI (43855) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (45995) DM-LOG: serial received msg->
length:24,
action:84,
resouce:2347,
msg_id:0,
data_length:1b
checksum enable
�[0m
�[0;32mI (45995) DM-LOG: remote_tcp_send_buffer:->
{"action": 84, "version":"zeico_3.0.0","resource_id":9031,"msg_id":0,"code":0,"data":{"source":"manual","deviceException":12582912,"useException":0,"power":0,"mode":0,"speed":100,"roll_enable":1,"roll_angle":90,"power_delay":0,"sound":0,"light":1,"child_lock":0,"temperature":0.0,"humidity":0.0,"ext1":97,"ext2":102,"ext3":13363,"ext4":14385,"ext5":943206968,"ext6":1630823777}}�[0m
�[0;32mI (46555) DM-LOG: remote_tcp_send_buffer:->
{"action": 1,"resource_id":127,"version":"zeico_3.0.0","data":{"comm_version":"dmiot_v1.1.0","rf_version":"v3.1.6","mcu_version":"fan_0001","signal":100}}�[0m
�[0;32mI (46635) DM-LOG: remote tcp clinet receive data: {"action":81,"resource_id":127,"version":"zeico_3.0.0","code":0}
�[0m
�[0;32mI (46865) DM-LOG: esp_get_free_heap_size:87160�[0m
�[0;32mI (49865) DM-LOG: esp_get_free_heap_size:87160�[0m
�`
dhewg commentedon Feb 28, 2025
That looks different to what my purifier prints. While I do see the raw serial communication, here it's just mentioned, but it's not clear if it's really the miot serial protocol, which is what we need.
So I think you need to try yourself and check what the esp32 gets from the mcu over serial.
For that you have two options:
All esp32 configs here have tx_pin=17 and rx_pin=16, so that's what I would try here first for either option.
For 2), make sure flashing via bootloader works, and use that to make a fw backup first.
d0np3p3 commentedon Feb 28, 2025
I am trying esptool right now, maybe you got a hint how to sniff the serial communication?
dhewg commentedon Mar 1, 2025
d0np3p3 commentedon Mar 5, 2025
on IO16 i only get some strings like "▒" with baudrate 115200 or"_YUAAX▒▒XUAA▒Ua▒" with 9600
any hints?
I Use Putty with a usb ttl
dhewg commentedon Mar 5, 2025
d0np3p3 commentedon Apr 3, 2025
I tried to backup the fw multiple times, mostly the esp reboots, the few times it worked i get different files, so i don't dare to flash esphome.
I will give it another try if i have more time.
Maybe anybody else with a dreammaker will give it a try.
d0np3p3 commentedon Apr 17, 2025
I think this fans are not using the Xiaomi Miot Serial Communication, so i gave up right now.
As workaround i use the dmiot2mqqt
If someone has done some more research, we could reopen the issue
hbgcreaghaht commentedon May 15, 2026
To avoid ESP32 reboot issue you need to short the Reset pin of the MCU to the GND.
on the fan board is 5 pins right next to ROHS sign that where you will find Reset and GND
I just soldered small SMD switch to be able to do it many times as I flash firmware
also in case you missed the Boot pin next to UART pins must be also connected to GND and ESP32 will show in serial that its In download mode
for the MCU side UART on IO 16 and 17 I noticed that baud rate 19200 works best.
when ESP32 is not in boot mode and MCU is works normal it seams like MCU is restarting the ESP every 5-10 minutes
d0np3p3 commentedon May 15, 2026
Let me know if u find something, My Backup contains my private wifi passwords... but I would like to get esphome working so tell me if i can support you.
BobeOlsen commentedon May 15, 2026
I working on it for three days already and no luck of successfully controlling it with custom firmware
a lot of info found all thanks to Claude etc.
main struggle is the communication to MCU what I discovered but not sure about it is that MCU constantly asking for wifi status and reboots ESP after 5-10 minutes I am assuming in order to be able to control it need more digging
so far what I can share is the data that was captured with simple UART sniffer Arduino sketch
I am no where near to be an expert in any of this its all just for fun to challenge my self and create something that works.
here is what I found useful so far
Physical buttons serial captured with UART sniffer Arduino sketch flashed on to ESP32 Wroom 32D UART pins GPIO16, GPIO17 MCU side UART
The fan board also have EEPROM in my case HT24LC02U3T026G6
Fan: dm-fan01_dmiot
Firmware: zeico_3.0.0
Protocol: DMIOT v1.1.0 (proprietary) + Miot (official)
Serial data received on boot with sniffer sketch UART IO 16 and 17
WiFi query from the MCU
HEX:
FA CE 00 09 02 00 78 00 00 00 00 00 00 4B ......x......K
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 9 | 0x09 | .
4 | 2 | 0x02 | .
5 | 0 | 0x00 | .
6 | 120 | 0x78 | x
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 0 | 0x00 | .
13 | 75 | 0x4B | K
──────────────────────────────────────
Fan state message from the MCU
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 00 64 00 00 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F5 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 0 | 0x00 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 245 | 0xF5 | .
──────────────────────────────────────
Power ON
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F6 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 246 | 0xF6 | .
──────────────────────────────────────
Power OFF
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 00 64 00 00 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F5 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 0 | 0x00 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 245 | 0xF5 | .
──────────────────────────────────────
Speed 1--->2
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 23 00 00 5A 00 00 01 01 00 .......#..Z.....
00 00 00 00 00 00 00 00 B5 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 35 | 0x23 | #
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 181 | 0xB5 | .
────────────────────────────────────
speed 2---->3
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 46 00 00 5A 00 00 01 01 00 .......F..Z.....
00 00 00 00 00 00 00 00 D8 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 70 | 0x46 | F
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 216 | 0xD8 | .
──────────────────────────────────────
Speed 3--->4
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F6 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼───────── 10BC8 ────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 246 | 0xF6 | .
──────────────────────────────────────
ESP32 Wroom 32D Rebooted (MCU reset the ESP)
ets Jun 8 2016 00:22:57
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:4980
load:0x40078000,len:16612
load:0x40080400,len:3500
entry 0x400805b4
Oscillation ON
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 01 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F7 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 1 | 0x01 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 247 | 0xF7 | .
──────────────────────────────────────
Oscillation OFF
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 00 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 F6 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 246 | 0xF6 | .
──────────────────────────────────────
Timer ON (entered timer selection if no button pressed second time it will exit without timer set)
HEX:
FA CE 00 09 02 00 78 00 00 00 00 00 00 4B ......x......K
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 9 | 0x09 | .
4 | 2 | 0x02 | .
5 | 0 | 0x00 | .
6 | 120 | 0x78 | x
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 0 | 0x00 | .
13 | 75 | 0x4B | K
──────────────────────────────────────
Timer set to 1 hour
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 3C 01 01 00 .......d..Z.<...
00 00 00 00 00 00 00 00 32 ........2
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 60 | 0x3C | <
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 50 | 0x32 | 2
──────────────────────────────────────
Timer set to 2 hours
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 78 01 01 00 .......d..Z.x...
00 00 00 00 00 00 00 00 6E ........n
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 120 | 0x78 | x
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 110 | 0x6E | n
──────────────────────────────────────
Timer set to 3 hours
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 B4 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 AA .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 180 | 0xB4 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 170 | 0xAA | .
──────────────────────────────────────
Timer set to 4 hours
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 64 00 00 5A 00 F0 01 01 00 .......d..Z.....
00 00 00 00 00 00 00 00 E6 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 100 | 0x64 | d
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 240 | 0xF0 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 230 | 0xE6 | .
──────────────────────────────────────
Normal mode———> Wind mode
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 00 ...$.#G.........
00 00 00 00 00 00 01 01 01 00 5A 00 00 01 01 00 ..........Z.....
00 00 00 00 00 00 00 00 54 ........T
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 0 | 0x00 | .
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 1 | 0x01 | .
24 | 1 | 0x01 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 84 | 0x54 | T
──────────────────────────────────────
Wind mode——> Night mode
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 01 02 00 5A 00 00 01 01 00 ..........Z.....
00 00 00 00 00 00 00 00 95 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 1 | 0x01 | .
24 | 2 | 0x02 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 149 | 0x95 | .
──────────────────────────────────────
Night mode——-> Normal Mode
HEX:
FA CE 00 24 84 23 47 00 00 00 00 00 1B 00 00 40 ...$.#G........@
00 00 00 00 00 00 01 01 00 00 5A 00 00 01 01 00 ..........Z.....
00 00 00 00 00 00 00 00 93 .........
DECIMAL VALUES:
Byte | Value (dec) | Value (hex) | ASCII
──────┼─────────────┼─────────────┼──────
0 | 250 | 0xFA | .
1 | 206 | 0xCE | .
2 | 0 | 0x00 | .
3 | 36 | 0x24 | $
4 | 132 | 0x84 | .
5 | 35 | 0x23 | #
6 | 71 | 0x47 | G
7 | 0 | 0x00 | .
8 | 0 | 0x00 | .
9 | 0 | 0x00 | .
10 | 0 | 0x00 | .
11 | 0 | 0x00 | .
12 | 27 | 0x1B | .
13 | 0 | 0x00 | .
14 | 0 | 0x00 | .
15 | 64 | 0x40 | @
16 | 0 | 0x00 | .
17 | 0 | 0x00 | .
18 | 0 | 0x00 | .
19 | 0 | 0x00 | .
20 | 0 | 0x00 | .
21 | 0 | 0x00 | .
22 | 1 | 0x01 | .
23 | 1 | 0x01 | .
24 | 0 | 0x00 | .
25 | 0 | 0x00 | .
26 | 90 | 0x5A | Z
27 | 0 | 0x00 | .
28 | 0 | 0x00 | .
29 | 1 | 0x01 | .
30 | 1 | 0x01 | .
31 | 0 | 0x00 | .
32 | 0 | 0x00 | .
33 | 0 | 0x00 | .
34 | 0 | 0x00 | .
35 | 0 | 0x00 | .
36 | 0 | 0x00 | .
37 | 0 | 0x00 | .
38 | 0 | 0x00 | .
39 | 0 | 0x00 | .
40 | 147 | 0x93 | .
──────────────────────────────────────
d0np3p3 commentedon May 15, 2026
Great captures, thanks! We (me & Claude Sonnet 4.6) analyzed the binary firmware dump alongside your UART captures and can now map the complete protocol.
Hardware confirmed:
Frame structure (MCU→ESP, 42 bytes):
FA CE00 2484=state frame,02=query23 47(state) /00 78(WiFi query)0x40normal,0x00wind mode only00=OFF,01=ON0x23=35%,0x46=70%,0x64=100%00=Normal,01=Wind,02=Night00=OFF,01=ON5Aalways0x3C=1h,0x78=2h,0xB4=3h,0xF0=4hWiFi Query (MCU→ESP, periodically):
The MCU sends this regularly and reboots the ESP if it gets no valid response. This is why you're seeing the 5–10 min reboot.
WiFi Response (ESP→MCU) — from firmware binary analysis:
The firmware contains a resource ID pair table. Resource
0x78(query) maps to0x70(response). So the correct reply is:81= ACK/Response70= response resource (paired with query resource0x78)0x02= WiFi connected →...00 70 02... C40x03= WiFi + cloud connected →...00 70 03... C50x01= connecting →...00 70 01... C3Best first attempt:
FACE0009810070020000000000C4The MCU likely stops rebooting the ESP once it sees status
02or03. Try03if02doesn't stop the reboot — it may expect cloud connectivity confirmation.Note: the response resource
0x70came from the firmware binary, not from your captures — you only sniffed RX (GPIO16). To fully confirm, sniff TX (GPIO17) with the original firmware running.d0np3p3 commentedon May 19, 2026
Hello @BobeOlsen, can you still switch between the original and esphome fw? i did some research, but i didn't get the uart to run, could you test some settings with the dreammaker app? i think Byte 27 ist the oscillation angle, it also can be moved left an right, also please set the timer to 8 hours in the app. i did some work here, but i can't confirm if it is working: https://github.com/d0np3p3/esphome-dreammaker-fan
BobeOlsen commentedon May 19, 2026
Hi
I did successfully revert back to OG firmware multiple times
I do not use the esphome for my needs i wanted to us it with homekit and homespan library in arduino
Here is what currently have have for byte map not sure how accurate is it but works for me
UART/Serial data in HEX captured on GPIO17 TX————>MCU RX while controlling fan from the App.
Turn ON with smart breeze mode
FA CE 00 0C 04 23 47 00 00 28 BC 00 03 00 00 01 2A
Turn ON with direct breeze mode
FA CE 00 0C 04 23 47 00 00 F1 BD 00 03 00 00 01 F4
Turn ON with direct breeze mode
FA CE 00 0C 04 23 47 00 00 47 30 00 03 00 00 01 BD
Turn OFF
FA CE 00 0C 04 23 47 00 00 0D 86 00 03 00 00 00 D8
Turn OFF
FA CE 00 0C 04 23 47 00 01 6F 8B 00 03 00 00 00 40
Turn OFF
FA CE 00 0C 04 23 47 00 00 02 63 00 03 00 00 00 AA
Switched to natural breeze
FA CE 00 0C 04 23 47 00 01 29 CE 00 03 00 02 01 40
Switched to direct breeze
FA CE 00 0C 04 23 47 00 01 59 38 00 03 00 02 00 D9
Set speed to level 2
FA CE 00 0C 04 23 47 00 01 61 ED 00 03 00 01 28 BD
Set speed to level 3
FA CE 00 0C 04 23 47 00 00 82 F9 00 03 00 01 3F 00
Set speed to level 4
FA CE 00 0C 04 23 47 00 01 2D 62 00 03 00 01 64 3A
Turned ON oscillation with preset 90 degree
FA CE 00 0C 04 23 47 00 00 E7 80 00 03 00 03 01 B0
Changed oscillation to 30 degree
FA CE 00 0C 04 23 47 00 00 BA 72 00 03 00 04 1E 93
Changed oscillation to 60 degree
FA CE 00 0C 04 23 47 00 00 49 07 00 03 00 04 3C D5
Changed oscillation to 120 degree
FA CE 00 0C 04 23 47 00 00 87 13 00 03 00 04 78 5B
Changed oscillation to 140 degree
FA CE 00 0C 04 23 47 00 00 80 B7 00 03 00 04 8C 0C
Notification sound ON
FA CE 00 0C 04 23 47 00 00 3F 7C 00 03 00 07 01 08
Notification sound OFF
FA CE 00 0C 04 23 47 00 00 6B 08 00 03 00 07 00 BF
Child Lock ON
FA CE 00 0C 04 23 47 00 00 17 F8 00 03 00 09 01 5E
Child Lock OFF
FA CE 00 0C 04 23 47 00 00 43 05 00 03 00 09 00 96
LED indication ON
FA CE 00 0C 04 23 47 00 01 6D DB 00 03 00 08 01 97
LED indication OFF
FA CE 00 0C 04 23 47 00 01 0C EF 00 03 00 08 00 49
Scheduled Turn-OFF set to OFF
FA CE 00 0D 04 23 47 00 01 6B C3 00 04 00 06 00 00 7C
Scheduled Turn-OFF set to 1
FA CE 00 0D 04 23 47 00 01 02 76 00 04 00 06 00 3C 02
Scheduled Turn-OFF set to 2
FA CE 00 0D 04 23 47 00 00 A0 9D 00 04 00 06 00 78 02
Scheduled Turn-OFF set to 3
FA CE 00 0D 04 23 47 00 00 0E C8 00 04 00 06 00 B4 D7
Scheduled Turn-OFF set to 4
FA CE 00 0D 04 23 47 00 00 9D DE 00 04 00 06 00 F0 B8
Scheduled Turn-OFF set to 5
FA CE 00 0D 04 23 47 00 01 12 FF 00 04 00 06 01 2C 8C
Scheduled Turn-OFF set to 6
FA CE 00 0D 04 23 47 00 00 C1 58 00 04 00 06 01 68 CF
Scheduled Turn-OFF set to 7
FA CE 00 0D 04 23 47 00 01 16 D5 00 04 00 06 01 A4 DE
Scheduled Turn-OFF set to 8
FA CE 00 0D 04 23 47 00 00 2C FE 00 04 00 06 01 E0 58
docs: add issue findings — MCU RST detail, baud rate note, protocol c…
d0np3p3 commentedon May 23, 2026
Thank you, i got it with your findings, i didn't get output from mcu.
Esphome runs and working, some small issues to fix,and test long running.
See my repo.
BobeOlsen commentedon May 23, 2026
Glad the info was useful that means I actually did something that works
Same here works fine with homekit also few tweaks needed
d0np3p3 commentedon May 23, 2026
@BobeOlsen Are you going to share your project?
BobeOlsen commentedon May 24, 2026
You mean the code/sketch?
I dont want to deal with all the github way of doing it like repo or whatever its called
I can just paste arduino sketch here and if it will help somebody else that would be nice
BobeOlsen commentedon May 26, 2026
here is the ArduinoIDE HomeSpan sketch that currently is running on the fans ESP32 Wroom 32D with Apple homekit just fine there is some minor issue that could be fixed I think but generally speaking it works great no random disconnection etc.
Also attached is reverse engineered protocol created by Claude AI
Thanks to d0np3p3 for checksum hint (plain 8-bit sum)
Now moving on to zhimi.fan.za3 Xiaomi Smartmi Standing Fan 2
ESP32_Wroom_32D_Fan_DM-FAN01-T_HomeKit.odt
Dream_Feel_Fan_DM_FAN01_HomeSpan_Ver3.ino.zip
Add Dream Maker Feel (Plus) to unsupported device list
d0np3p3 commentedon Jul 31, 2026
Hello has anybody, maybe @BobeOlsen access to the mcu communication and can test what happens if you try to pair a remote, I am still trying to get it work....
Everything else is working fine with Esphome.
[
d0np3p3 commentedon Aug 3, 2026
Correction to my earlier comment in this thread — the
0x70response I postedwas speculation read out of the firmware binary, never verified against a
real capture. It is wrong, and I'd rather flag it than leave people building on
it.
Wrong (my earlier guess):
Correct, confirmed from live UART captures (original firmware running
against a simulated MCU on a test bench):
The MCU polls with
action:2, resource:0x0078roughly every 60 s, and the ESPanswers
action:0x82on the same resource. The response payload is 56 bytes:comm_version, ASCII, null-paddedfirmware_version, ASCII, null-paddedWithout a response the MCU pulls the ESP's EN pin low and reboots it after
about four minutes, so this one matters if you're writing your own firmware.
This is also consistent with @BobeOlsen's independent app captures in this
thread — those matched our resource mapping 1:1, including the exact angle
bytes (
0x1E/3C/78/8C= 30/60/120/140°) and timer values(
0x3C/78/B4/F0= 1–4 h).Sorry for the noise. Full protocol notes here:
https://github.com/d0np3p3/esphome-dreammaker-fan/blob/main/PROTOCOL.md
Optional addition — only if you want to mention the remote
The BLE remote work is on a beta branch and needs a per-device key, so it may
be more noise than help for that thread. Include only if it seems welcome:
Add Dream Maker Feel (Plus) to unsupported device list